STS Corvette Forum

kensmith · kensmith

I have searched the web for a 14" X 2 1/2" round paper air filter with no luck. Do they not make them?

Babbah · Babbah

I'm attempting to change the bulbs on my 67 now and I must admit it has been a very frustrating experience. I have the speedo and tach disconnected and the oil line still attached. I really don't want to touch it as its bone dry and does not leak. I see enough extra line at the fire wall (coils) so I'm not worr...

ffas23 · ffas23

Finally fixed a overheating problem at idle or in bumper to bumper traffic so to say that I was having on and off for quite awhile. After much research I found that my Vacuum Cannister to the distributor was the problem all along. Replaced it recently a few weeks ago and even in this very hot weather I have...

ffas23 · ffas23

Been kicking it around a long time (10 years LOL) about getting my Power Booster anodized. Just never could find the time to take the one out of my '67 during the Winter to send it out to be done. Last month while surfing on the net I happened on Ebay and was looking at brand new Power Boosters for sale th...

ffas23 · ffas23

It’s likely you’ve read in the past about some poor soul whose cars went up in flames and he didn’t have insurance coverage. But what if he had insurance? Would the pain be any less great? When you’ve owned a car for 44 years, no amount of insurance can cover the loss or pain. Here’s the story of John Hibbel...

L79racer · L79racer

Just found this site. Looking to see if there are any early 67's here. I own # 31. Looking to keep track of the very early ones. Thanks. Vinny

ffas23 · ffas23

Posted in NewsEmailFacebookTwitterPrint Two ’67 Corvettes and One VIN Not Adding Up For Ohio Investigators by Lindsey Fisher on May 31, 2012 Comments Image: CorvetteBlogger.com Vehicle Identification Numbers are important; they give your car its unique identity right from the factory. Bu...

ffas23 · ffas23

Just installed a new 10-1/2" Clutch in my '67 Coupe a week ago and new Clutch Rod and Pivot Pin just the other day that was worn almost half way through. Also needed to send the Flywheel out to be ground down. The clutch was chattering somewhat since I purchased this Coupe 10 years ago but drove fi...

vett boy · vett boy

Well sort off -----First I have not seen the car and I have no photos . The car is a 55 vett in pretty good condition that the owner stored in his basement for the past 41 years .The basement was heated and very dry .Owner took it out last week and it started with a new battery ,he drove it for a couple miles and...

zathrus · zathrus

On the other Forum I been watching a debate about motor oils for Flat Tappet Cams.I am about to try the Brad Penn 10W - 30 oil. I have been using Castrol but it seems the Wal-Mart self oils are no longer suitable for the older cars. Specifications changed in 2005.Have you heard of this problem with ZDDP lev...

kensmith · kensmith

I have A/C and running a 16" Spal High Output puller electric fan. It has the straight blades and is really noisy. I'm thinking of buying the Spal 16" High Output curved blade fan for less noise. I have heard they are much quieter. Any opinions?

Sebringbill · Sebringbill

Attention all SACC/SSSACC members! Bill Herron (aka SebringBill) will be hosting a Solid Axle event in conjunction with "Corvettes on the Circle" (at St Armands Circle). Starting Friday, May 6th I'll be having a technical session at my Garage Mahal/Motorhead Lounge in Sarasota FL. Wa...

kensmith · kensmith

There isn't anything easy about working on a C2. To replace the battery I had to drain and remove the expansion tank, move heater hoses, work around A/C lines, and stand the batteries on end to get them in and out. Then reverse the same stuff. Took me two hours to do a 5 minute job on my daily drivers.

kensmith · kensmith

Well, my cheap NAPA 60amp re-manufactured Delco-Remy alternator started making crackling noises when my a/c and electric fan are both on. I noticed with the electric radiator fan going and turning the a/c on, the amp meter takes a pretty good dive to the neg side. Turn the a/c off it jumps up to the at i...

kensmith · kensmith

Decided to buy a set of used 1988 Fiero seats and whacked off the headrests and cover them in leather to install in my 65 vette. Mr Mike Fiero seat covers were ordered and I actually did the installation. The leather covers were about 750 shipped, used seats were 130 shipped from a guy in Arizona, the plas...

kensmith · kensmith

I am going to insulate my 65 coupe next week while on vacation. I have the double sided foil from EZ-Cool called Low-E. I am going to do the floor under all the carpet and if I have enough I will also do the headliner. I have had the seats out and the chrome console before but was wondering if there are any tips...

ffas23 · ffas23

Finally uncovered the C-2 sitting since last Fall. . The plans today are to dust it off and take a ride sometime this afternoon. Looking forward to it. We had a good rain last night and it is a bit cooler today so not having A/C shouldn't be a problem later on I am hoping. Too many things in the way once agai...

ffas23 · ffas23

I got the chance to see the movie 7 pounds on Thursday. My daughter had the DVD. I recommend checking out the movie if you haven't seen it yet. Its a movie staring actor Will Smith. There are a few scenes in the movie where Will Smith is driving a 1964 Stingray Coupe, light blue with a Big Block Hood. The m...

vett boy · vett boy

The first and second seasons are available via NEXFLIX .I've ordered the first season.

Corvette Forum Member Wins It Big · ffas23

A Corvette forum member possibly won it big Christmas day in the The 2009 Corvette Dream Giveaway. Dave Melitski won both a Restored 1967 Corvette Roadster 427-390HP and a brand new one of a kind Hero Edition 2009 ZRI. Nice win but the IRS will be looking for the tax money my guess to be over $60k. Lin...

vett boy · vett boy

Anyone know the story about Corvette #29 ?

ffas23 · ffas23

vett boy · vett boy

A friend of mine has a decent 66 vert ,4sp that will probibly be coming up for sale in the next few months.He has not set a price yet and the car is not original but looks stock and is in semi show condition.

ffas23 · ffas23

Ken or anyone else still on the CF Forum. If you take a look up on your left you will see my newest avatar. Actually someone took one of the pictures of my 67 Coupe on the CF Forum that just so happened to come on that forum a couple of years ago and made this for me. He did it for free and did a few others but wa...

Sebringbill · Sebringbill

http://forums.corvetteforum.com/c1-and-c2-corvettes/2441308-umm-splain-this-lucy-53-29-x2.html

kensmith · kensmith

Trying to find a 10" or 12" diameter DROP base air cleaner for my Holley Street Avenger. The 14" I have works but if I can find a smaller diameter I can go with a taller filter VS the 2" I have now. A 2 1/2" filter would give me more room above the carburetor. I have a feeling the li...

kensmith · kensmith

I have Moog springs and they are 4" shorter than stock progressive springs. I am going to try and remove them by removing the lower control arm at the frame. I am thinking I can use a floor jack to support the control arm and then remove the 2 bolts holding it to the frame. Lower the jack to remove the s...

kensmith · kensmith

I ordered new pulleys per suggestions on the corvetteforum.com to increase water pump flow. Now have a 7.3" crank pulley VS the 6.7" that was on the motor. And a 6.4" VS 7.0" water pump pulley. Did the swap to increase water pump output at lower RPM per forum suggestions. The prob...

ffas23 · ffas23

Just received an email this morning from Corvette America. Have done plenty of business with them over the years. Anyway this email I received was an announcement that Corvette America now has an exact replacement AM/FM Radio for the C-2 Corvette from '63-'67 that has all the bells and whistles buil...

kensmith · kensmith

I'm going to replace my front springs and was wondering what size pickle fork I need to separate the ball joint? 65 coupe.

Topic		Started By	Replies	Views	Last Post
	Need to buy a 14" X 2 1/2" air filter. (Preview) I have searched the web for a 14" X 2 1/2" round paper air filter with no luck. Do they not make them?	kensmith	10	13856	Aug 20 3:25 AM, 2013 by larryc
	Changing Dash Bulbs on C2 (67) - Help (Preview) I'm attempting to change the bulbs on my 67 now and I must admit it has been a very frustrating experience. I have the speedo and tach disconnected and the oil line still attached. I really don't want to touch it as its bone dry and does not leak. I see enough extra line at the fire wall (coils) so I'm not worr...	Babbah	2	1998	Apr 21 4:49 AM, 2013 by ffas23
	Overheating Problem At Idle Corrected Finally (Preview) Finally fixed a overheating problem at idle or in bumper to bumper traffic so to say that I was having on and off for quite awhile. After much research I found that my Vacuum Cannister to the distributor was the problem all along. Replaced it recently a few weeks ago and even in this very hot weather I have...	ffas23	4	2538	Aug 28 1:05 AM, 2012 by ffas23
	New Project For The Fall (Preview) Been kicking it around a long time (10 years LOL) about getting my Power Booster anodized. Just never could find the time to take the one out of my '67 during the Winter to send it out to be done. Last month while surfing on the net I happened on Ebay and was looking at brand new Power Boosters for sale th...	ffas23	1	1799	Aug 14 2:27 AM, 2012 by vett boy
	Man’s Prized Corvettes, Toys Lost In Garage Fire (Preview) It’s likely you’ve read in the past about some poor soul whose cars went up in flames and he didn’t have insurance coverage. But what if he had insurance? Would the pain be any less great? When you’ve owned a car for 44 years, no amount of insurance can cover the loss or pain. Here’s the story of John Hibbel...	ffas23	2	1789	Jul 15 11:18 PM, 2012 by vett boy
	Any early 67's? (Preview) Just found this site. Looking to see if there are any early 67's here. I own # 31. Looking to keep track of the very early ones. Thanks. Vinny	L79racer	2	1802	Jul 15 11:16 PM, 2012 by vett boy
	Two ’67 Corvettes and One VIN Not Adding Up For Ohio Investigators (Preview) Posted in NewsEmailFacebookTwitterPrint Two ’67 Corvettes and One VIN Not Adding Up For Ohio Investigators by Lindsey Fisher on May 31, 2012 Comments Image: CorvetteBlogger.com Vehicle Identification Numbers are important; they give your car its unique identity right from the factory. Bu...	ffas23	0	1692	Jun 1 4:45 AM, 2012 by ffas23
	New Clutch In My '67 (Preview) Just installed a new 10-1/2" Clutch in my '67 Coupe a week ago and new Clutch Rod and Pivot Pin just the other day that was worn almost half way through. Also needed to send the Flywheel out to be ground down. The clutch was chattering somewhat since I purchased this Coupe 10 years ago but drove fi...	ffas23	0	1818	May 18 12:28 PM, 2012 by ffas23
	Barn find 55 (Preview) Well sort off -----First I have not seen the car and I have no photos . The car is a 55 vett in pretty good condition that the owner stored in his basement for the past 41 years .The basement was heated and very dry .Owner took it out last week and it started with a new battery ,he drove it for a couple miles and...	vett boy	6	2086	Feb 7 6:36 AM, 2012 by Sebringbill
	Motor oil for Flat Tappet Cams (Preview) On the other Forum I been watching a debate about motor oils for Flat Tappet Cams.I am about to try the Brad Penn 10W - 30 oil. I have been using Castrol but it seems the Wal-Mart self oils are no longer suitable for the older cars. Specifications changed in 2005.Have you heard of this problem with ZDDP lev...	zathrus	9	3759	May 7 11:33 AM, 2011 by kensmith
	Spal 16" electric fan swap? (Preview) I have A/C and running a 16" Spal High Output puller electric fan. It has the straight blades and is really noisy. I'm thinking of buying the Spal 16" High Output curved blade fan for less noise. I have heard they are much quieter. Any opinions?	kensmith	10	2835	May 2 2:10 PM, 2011 by ffas23
	Wanna See the SR-2 Up Close? (Preview) Attention all SACC/SSSACC members! Bill Herron (aka SebringBill) will be hosting a Solid Axle event in conjunction with "Corvettes on the Circle" (at St Armands Circle). Starting Friday, May 6th I'll be having a technical session at my Garage Mahal/Motorhead Lounge in Sarasota FL. Wa...	Sebringbill	3	1862	Apr 10 2:56 PM, 2011 by vett boy
	Battery is in..............whew (Preview) There isn't anything easy about working on a C2. To replace the battery I had to drain and remove the expansion tank, move heater hoses, work around A/C lines, and stand the batteries on end to get them in and out. Then reverse the same stuff. Took me two hours to do a 5 minute job on my daily drivers.	kensmith	14	2997	Oct 31 5:02 PM, 2010 by Sebringbill
	Need a new alternator for my C2.....but which one? (Preview) Well, my cheap NAPA 60amp re-manufactured Delco-Remy alternator started making crackling noises when my a/c and electric fan are both on. I noticed with the electric radiator fan going and turning the a/c on, the amp meter takes a pretty good dive to the neg side. Turn the a/c off it jumps up to the at i...	kensmith	36	4701	Aug 17 9:24 PM, 2010 by Sebringbill
	1988 Fiero seats for my 65 vette..........before and after. (Preview) Decided to buy a set of used 1988 Fiero seats and whacked off the headrests and cover them in leather to install in my 65 vette. Mr Mike Fiero seat covers were ordered and I actually did the installation. The leather covers were about 750 shipped, used seats were 130 shipped from a guy in Arizona, the plas...	kensmith	6	2787	Aug 9 12:24 PM, 2010 by kensmith
	Interior insulation help (Preview) I am going to insulate my 65 coupe next week while on vacation. I have the double sided foil from EZ-Cool called Low-E. I am going to do the floor under all the carpet and if I have enough I will also do the headliner. I have had the seats out and the chrome console before but was wondering if there are any tips...	kensmith	5	2405	Jul 31 2:45 AM, 2010 by ffas23
	Finally Taking My C-2 Out For A Ride In 2010 (Preview) Finally uncovered the C-2 sitting since last Fall. . The plans today are to dust it off and take a ride sometime this afternoon. Looking forward to it. We had a good rain last night and it is a bit cooler today so not having A/C shouldn't be a problem later on I am hoping. Too many things in the way once agai...	ffas23	9	2770	Jun 29 5:42 AM, 2010 by vett boy
	Saw 7 Pounds Yesterday (Preview) I got the chance to see the movie 7 pounds on Thursday. My daughter had the DVD. I recommend checking out the movie if you haven't seen it yet. Its a movie staring actor Will Smith. There are a few scenes in the movie where Will Smith is driving a 1964 Stingray Coupe, light blue with a Big Block Hood. The m...	ffas23	0	1809	Feb 26 1:12 AM, 2010 by ffas23
	Route 66 TV series (Preview) The first and second seasons are available via NEXFLIX .I've ordered the first season.	vett boy	7	3306	Feb 6 4:57 PM, 2010 by Mr.Muffler
	Corvette Forum Member Wins It Big (Preview) A Corvette forum member possibly won it big Christmas day in the The 2009 Corvette Dream Giveaway. Dave Melitski won both a Restored 1967 Corvette Roadster 427-390HP and a brand new one of a kind Hero Edition 2009 ZRI. Nice win but the IRS will be looking for the tax money my guess to be over $60k. Lin...	ffas23	6	3015	Jan 18 1:52 PM, 2010 by kensmith
	Corvette 29 (Preview) Anyone know the story about Corvette #29 ?	vett boy	1	1831	Nov 26 6:57 PM, 2009 by Sebringbill
	Cool 1963 Corvette Commercial (Preview)	ffas23	2	2064	Nov 26 12:15 PM, 2009 by kensmith
	66 for sale (Preview) A friend of mine has a decent 66 vert ,4sp that will probibly be coming up for sale in the next few months.He has not set a price yet and the car is not original but looks stock and is in semi show condition.	vett boy	1	1924	Nov 3 1:49 AM, 2009 by ffas23
	NEED A FAVOR (Preview) Ken or anyone else still on the CF Forum. If you take a look up on your left you will see my newest avatar. Actually someone took one of the pictures of my 67 Coupe on the CF Forum that just so happened to come on that forum a couple of years ago and made this for me. He did it for free and did a few others but wa...	ffas23	15	2808	Oct 30 6:42 AM, 2009 by vett boy
	I Know, Fred... (Preview) http://forums.corvetteforum.com/c1-and-c2-corvettes/2441308-umm-splain-this-lucy-53-29-x2.html	Sebringbill	18	4357	Oct 24 12:04 AM, 2009 by Sebringbill
	air cleaner (Preview) Trying to find a 10" or 12" diameter DROP base air cleaner for my Holley Street Avenger. The 14" I have works but if I can find a smaller diameter I can go with a taller filter VS the 2" I have now. A 2 1/2" filter would give me more room above the carburetor. I have a feeling the li...	kensmith	6	2300	Oct 3 12:52 PM, 2009 by kensmith
	Remove and re-install front springs. (Preview) I have Moog springs and they are 4" shorter than stock progressive springs. I am going to try and remove them by removing the lower control arm at the frame. I am thinking I can use a floor jack to support the control arm and then remove the 2 bolts holding it to the frame. Lower the jack to remove the s...	kensmith	8	3301	Oct 3 10:42 AM, 2009 by kensmith
	Oversize crank pulley and lower radiator hose (Preview) I ordered new pulleys per suggestions on the corvetteforum.com to increase water pump flow. Now have a 7.3" crank pulley VS the 6.7" that was on the motor. And a 6.4" VS 7.0" water pump pulley. Did the swap to increase water pump output at lower RPM per forum suggestions. The prob...	kensmith	5	2110	Sep 22 2:06 PM, 2009 by kensmith
	Corvette America (Preview) Just received an email this morning from Corvette America. Have done plenty of business with them over the years. Anyway this email I received was an announcement that Corvette America now has an exact replacement AM/FM Radio for the C-2 Corvette from '63-'67 that has all the bells and whistles buil...	ffas23	8	2689	Sep 18 9:07 AM, 2009 by ffas23
	pickle fork size? (Preview) I'm going to replace my front springs and was wondering what size pickle fork I need to separate the ball joint? 65 coupe.	kensmith	4	1909	Sep 8 10:58 AM, 2009 by kensmith
1 2 3 4 > Last» \| Page of 4 sorted by